| Both sides previous revision
Previous revision
Next revision
|
Previous revision
Last revision
Both sides next revision
|
docs:manual [2019/02/05 21:42]
Melissa Glidewell [Overview] |
docs:manual [2019/02/27 23:02]
Melissa Glidewell [Mount] |
| ====== Overview ====== | ====== Overview ====== |
| {{section>modular_manual#overview&noheader}} | {{section>modular_manual#overview&noheader}} |
| The advantage of the diSPIM being dual-sided is that the role of the two objectives can be reversed to collect a second stack from a perpendicular direction. The two optical paths are usually symmetric, and are designated Path A and Path B. (The two paths are described in detail in the [[docs:mm_dispim_plugin_user_guide#diSPIM Plugin User Guide]].) Registration and joint deconvolution merge the two datasets for improved resolution isotropy. | |
| | The core assembly, the SPIM head, can be mounted on various inverted microscopes. Thus far, microscope-specific adapter brackets((Attaching the SPIM precludes the use of the transmitted light optics because the brackets utilize the transmitted light pillar mounting point.)) exist for the following microscopes: |
| | * ASI RAMM frame (<imgref SPIM_Figure>) |
| | * Leica DMI-6000 |
| | * Nikon TE-300, Ti, TE-2000, Ti2 |
| | * Olympus IX-71/81, IX-73/83 |
| | * Zeiss Axio-Observer |
| |
| <imgcaption SPIM_Figure|Typical complete diSPIM system on RAMM frame showing major components. 1) SPIM-MOUNT , 2) SPIM-RAMM , 3) SPIM arm mount (RAO-0046 ), 4) piezo objective mover APZOBJ-200 or similar, 5) MIM inverted microscope with LS-50M stage, 6) CDZ-1000 centering stage or CDZ-R block, 7) LS-50M stage, 8) MIM-CUBE-II w/ mirror, 9) MIM-CUBE-II w/ fluorescence filters, 10) C60-TUBE_B imaging tube lens, 11) C60-TUBE_160 scanner tube lens, 12) 50mm extension tube, 13) MM-SCAN_1M light sheet scanner, 14) MS-2500 XY stage.>{{:docs:manual:dispim_figure.jpg?600| Typical complete diSPIM system on RAMM frame showing major components.}}</imgcaption> | <imgcaption SPIM_Figure|Typical complete diSPIM system on RAMM frame showing major components. 1) SPIM-MOUNT , 2) SPIM-RAMM , 3) SPIM arm mount (RAO-0046 ), 4) piezo objective mover APZOBJ-200 or similar, 5) MIM inverted microscope with LS-50M stage, 6) CDZ-1000 centering stage or CDZ-R block, 7) LS-50M stage, 8) MIM-CUBE-II w/ mirror, 9) MIM-CUBE-II w/ fluorescence filters, 10) C60-TUBE_B imaging tube lens, 11) C60-TUBE_160 scanner tube lens, 12) 50mm extension tube, 13) MM-SCAN_1M light sheet scanner, 14) MS-2500 XY stage.>{{:docs:manual:dispim_figure.jpg?600| Typical complete diSPIM system on RAMM frame showing major components.}}</imgcaption> |
| {{section>modular_manual#camera_setup&noheader}} | {{section>modular_manual#camera_setup&noheader}} |
| |
| ==== Mount ==== | ==== Mount Camera Tube Lenses ==== |
| Tools: M5 hex driver\\ | Tools: M5 hex driver\\ |
| In the standard configuration for diSPIM on a RAMM frame, as in <imgref SPIM_Figure>, each camera tube lens is fastened to the SPIM-MOUNT((Other common configurations use a post mount system to minimize vibration from the camera's fans, or to accommodate an FTP system in lieu of a RAMM frame.)) with a ring clamp. The end of the tubes should come within approximately 1 mm from the upper (mirror) CUBE-IIIs. When the objectives are lowered into position for viewing a sample, adjust the bolts holding the tube support arms so the camera tube lenses are centered on the CUBE-IIIs. \\ | In the standard configuration for diSPIM on a RAMM frame, as in <imgref SPIM_Figure>, each camera tube lens is fastened to the SPIM-MOUNT((Other common configurations use a post mount system to minimize vibration from the camera's fans, or to accommodate an FTP system in lieu of a RAMM frame.)) with a ring clamp. The end of the tubes should come within approximately 1 mm from the upper (mirror) CUBE-IIIs. When the objectives are lowered into position for viewing a sample, adjust the bolts holding the tube support arms so the camera tube lenses are centered on the CUBE-IIIs. \\ |
